SupaBrake-IIT (Third brake light) For Cars!

currently off line. email for information

(3 reviews) Write a Review
Availability:
Ships 1 to 3 days
Bulk Pricing:
Buy in bulk and save
SB2-T Kit. Shown is actual SB-T module with Posi-Locks and magnet.

Based on the SB-II firmware and designed for a vehicle's high-mounted stop light where only 2 wires are present. Such as those commonly found on the rear windows of trucks and cars. The SB-T requires only one signal wire and a ground return wire to implement; No need for a third constant 12V power. The internal circuit uses advance super-capacitor technologies to harness and store power each time the brakes are applied. The firmware allows the customer to select and store 1 of 10 pre-defined profiles into memory in a tiny 35mm x 24mm x 8mm waterproof module where 3 different modulation frequencies and 3 sets of algorithm constants are stored. As a result a 3x3 combination matrix creates 9 possible modulation profiles.

FUNCTION
Vizible Technologies' SupaBrake modulators are designed to enhance the reaction time of the vehicle behind you. It is designed to pulsate your vehicle's brake light(s) with a variable number of flashes calculated by its embedded algorithm. The algorithm is based on the rate at which you apply your brakes. As a result, the brake light(s) are flashed in a more subtle manner at lower speeds(when brakes are frequently used), and more aggressively at higher speeds(when brakes are not used for longer time intervals). Whereas other simpler products on the market that continuously "blink" their brake light(s) with an annoying repeating sequence - each and every time their brakes are applied! Our Supabrake product pulses in driving conditions when you need to get the immediate attention of drivers without annoying them.

Upon applying the brakes, the SupaBrake sends a burst of pulses to your motorcycle's brake light(s). The duration of the burst is a function of the time elapsed between the current brake cycle and the previous. After the burst, the unit allows the rear brake light to function normally(solid brake light). This algorithm is designed to eliminate target fixation as found in cheaper, passive versions that continuously "blink" the brake light(s) even though the vehicle is at a complete stop.

Example at low speed
When the frequency at which the driver/rider applies the brakes increases, (i.e. during low speeds such as city driving), the shorter the burst of flashes to the rear brake(s) light will be. If the brakes are applied within 0 - 12 seconds, the brake light will NOT flash - thus allowing it to function normally (solid brake light). This condition is most valuable during heavy stop-and-go traffic so as not to annoy the person or police in the vehicle behind you.

Example at cruising speed
When the frequency at which the driver/rider applies the brakes decreases, (i.e. at cruising speed), the longer the burst to the rear brake light will be. This condition is most valuable during quick sudden decelerations at speeds which require quick reaction to changes in traffic conditions or other driver's intentions. It has been scientifically proven that a quick flashing of a vehicle's brakes will alert the driver behind much sooner ... and the SupaBrake Flasher does this for you.

FEATURES & BENEFITS

  • User profile select
    Preloaded with 10 field selectable/programmable profiles*. Option to upload a fully customizable "11th profile" available.
  • Input de-bounce
    This feature allows the user to quickly “tap” the brake lever or pedal without the algorithm inducing its flash routine or resetting. In an event of a "tap", the brake light will function normally and will appear as an ordinary tap of the brakes. Another aspect to this feature is that it allows the user to initiate a quick speed check on the rear brakes before a full application of the front brakes. In this case the algorithm will trigger a burst after full brake application.
  • Force-Flash retriggering
    This technology, unique to Vizible Technologies, allows the rider to manually induce a flash routine after the initial application of the brakes. This is useful when stopped alone at a red light or in traffic to alert vehicles approaching from behind. Example: Press and hold the brakes for >3seconds. Quickly release and reapply the brakes within half second. The unit will output a burst of flashes.
  • Decaying flash routine
    Each pulse period is gradually increased from the previous pulse. This gives the given burst cycle a "de-acceleration" illusion when viewed from behind at speed. In other words, the routine will start with a faster frequency and end with a slower frequency.
  • Defeat Mode
    This feature allows the rider to quickly bypass all the functions of the SupaBrake without having to physically remove the unit from the motorcycle. If need be, the functionality of your brake light can easily revert to stock condition.
  • Simple Plug & Ride Installation
  • Miniature size
  • Works with all OEM light devices (incandescent, LED or halogen)
  • Algorithm with custom flash routine programming available
  • Ships within 12-48hrs
  • 10 year limited warranty
  • Legal in all 50 States. (The running light never modulates. Only the brake light)
  • High temperature tolerance
  • Vibration and shock tested
  • All weather proof (IEC 529 IP 6.7 standards)
  • Surface mount electronics
  • Powerful micro-controller with "watch-dog" technology
  • MOSFET driven
  • Opto-Isolated from vehicle's electrical systems
  • High load current
  • Low supply(Quiescent) current
  • De-bounce feature
    Ability to tap brakes without resetting the algorithm
  • Grace period between brake applications
    The flasher won't activate if brakes are applied again within a certain period of time
  • Force-Flash retrigger
    Ability to induce a burst of flashes while stopped at a stop light if another vehicle approaches from behind
  • Decaying flash routine

Don't put other outdated bulkier modules on your vehicle that pulsate your brake light each and every time you apply your brakes. Most of these cheaper engineered modules will continue to flash your brake light(s) with the same irritating routine even when you are completely stopped in traffic. This is not only illegal and annoying it detracts from the visual appearance of your vehicle. You get what you pay for.

  • SB2-T USER GUIDE - (pdf)
  • SB2-T USER GUIDE(German) - (pdf)
  • SB2-T Quick Vid. Profile#5 - (mov)
  • STANDARD ALGORITHM CHART - (pdf)

3 Reviews Hide Reviews Show Reviews

  • 5
    awesome

    Posted by james on 8th Aug 2015

    I had some difficulties with install that was pretty much my fault I couldn't figure out which wires went where. Customer service was great! The product was going to be delivered late but I got an email letting me know ahead of time. And then when I got it It was a hand written note attached again apologizing for the lateness. I would buy from this company again

  • 5
    The 'smart' led flasher

    Posted by Unknown on 31st May 2015

    It had the perfect 'smart' algorithm to not go too crazy with flashes, and it's working extremely well with an LED light bar within a car.

  • 5
    Another great product!

    Posted by Larry Carr on 12th Oct 2014

    I installed this product on my Honda GL1800 motorcycle to flash the LED light bar that is incorporated into the trunk lid spoiler. Very simple install and it works flawlessly. Great product.