Loading... Please wait...
  • SB3 as seen with an OEM connector. A complete Plug and Play solution.
The ultimate in motorcycle brake light modulator. Slap it in and go!
  • The new SB3 is encapsulated in epoxy for the ultimate protection against grease, dirt and water. CNC'd out of Delrin (R) material case makes it virtually indestructible. Super miniature design packs a whole lot of functions! Big punch in a tiny package. Now comes with 108 thousands profiles! More then enough to meet any ones needs.
  • SB3 as seen with an OEM connector plus the extra harness option to allow access to +12V(switched), Stock Brake signal, Modulated Brake Signal and Ground. Mating connector for extra harness not shown.

SupaBrake-3 TRIUMPH

1 - 5 biz dayz. Need it soon? Leave us note at checkout.
Calculated at checkout

Product Description

The new SB3 for your Triumph!

It's a proven fact that motorcycles can decelerate more rapidly than most cars and trucks. The combination of a motorcycle's narrow profile and the brisk change in velocity during braking is the most common cause of rear end accidents involving motorcycles, and often the results are fatal to the rider. Vizible Technologies' SupaBrake modulators are designed to enhance the reaction time of the vehicle behind you. It is designed to pulsate your vehicle's brake light(s) with a variable number of flashes calculated by its embedded algorithm. The algorithm is based on the rate at which you apply your brakes. As a result, the brake light(s) are flashed in a more subtle manner at lower speeds(when brakes are frequently used), and more aggressively at higher speeds(when brakes are not used for longer time intervals). Whereas other simpler products on the market that continuously "blink" their brake light(s) with an annoying repeating sequence - each and every time their brakes are applied! Our Supabrake product pulses in driving conditions when you need to get the immediate attention of drivers without annoying them.

Upon applying the brakes, the SupaBrake sends a burst of pulses to your motorcycle's brake light(s). The duration of the burst is a function of the time elapsed between the current brake cycle and the previous. After the burst, the unit allows the rear brake light to function normally(solid brake light). This algorithm is designed to eliminate target fixation as found in cheaper, passive versions that continuously "blink" the brake light(s) even though the vehicle is at a complete stop.

Example at low speed
When the frequency at which the driver/rider applies the brakes increases, (i.e. during low speeds such as city driving), the shorter the burst of flashes to the rear brake(s) light will be. If the brakes are applied within 0 - 12 seconds, the brake light will NOT flash - thus allowing it to function normally (solid brake light). This condition is most valuable during heavy stop-and-go traffic so as not to annoy the person or police in the vehicle behind you.

Example at cruising speed
When the frequency at which the driver/rider applies the brakes decreases, (i.e. at cruising speed), the longer the burst to the rear brake light will be. This condition is most valuable during quick sudden decelerations at speeds which require quick reaction to changes in traffic conditions or other driver's intentions. It has been scientifically proven that a quick flashing of a vehicle's brakes will alert the driver behind much sooner ... and the SupaBrake Flasher does this for you.


  • User profile select
    108,801 field selectable/programmable profiles!
  • Self-contained profile selection. No need for external hardware/software etc.
  • On-The-Fly profile review. Allows rider to see what the internal settings of the algorithm is
  • Selectable Grace period between brake applications
    The flasher won't activate if brakes are applied again within a certain period of time
  • Input de-bounce
    This feature allows the user to quickly “tap” the brake lever or pedal without the algorithm inducing its flash routine or resetting. In an event of a "tap", the brake light will function normally and will appear as an ordinary tap of the brakes. Another aspect to this feature is that it allows the user to initiate a quick speed check on the rear brakes before a full application of the front brakes. In this case the algorithm will trigger a burst after full brake application.
  • Force-Flash retriggering
    This technology, unique to Vizible Technologies, allows the rider to manually induce a flash routine after the initial application of the brakes. This is useful when stopped alone at a red light or in traffic to alert vehicles approaching from behind. Example: Press and hold the brakes for >3seconds. Quickly release and reapply the brakes within half second. The unit will output a burst of flashes.
  • Decaying flash routine
    Each pulse period is gradually increased from the previous pulse. This gives the given burst cycle a "de-acceleration" illusion when viewed from behind at speed. In other words, the routine will start with a faster frequency and end with a slower frequency.
  • Defeat Mode
    This feature allows the rider to quickly bypass all the functions of the SupaBrake without having to physically remove the unit from the motorcycle. If need be, the functionality of your brake light can easily revert to stock condition.
  • Simple Plug & Ride Installation
  • Bypass Mode allows the user to bypass all the features of the SupaBrake without having to physically remove the unit from the motorcycle..
  • Simple Plug & Ride Installation
  • Miniature size
  • Works with all OEM light devices (incandescent, LED or halogen)
  • Algorithm with custom flash routine programming available
  • Ships within 12-48hrs
  • 10 year limited warranty
  • Legal in all 50 States. (The running light never modulates. Only the brake light)
  • High temperature tolerance
  • Vibration and shock tested
  • All weather proof (IEC 529 IP 6.7 standards)
  • Surface mount electronics
  • Powerful micro-controller with "watch-dog" technology
  • MOSFET driven
  • Opto-Isolated from vehicle's electrical systems
  • High load current
  • Low supply(Quiescent) current
  • OEM connectors
  • De-bounce feature
    Ability to tap brakes without resetting the algorithm
  • Variable number of flashing output based on a 100% programmable algorithm
  • Force-Flash retrigger
    Ability to induce a burst of flashes while stopped at a stop light if another vehicle approaches from behind
  • Decaying flash routine

Don't put other outdated bulkier modules on your motorcycle that pulsate your brake light each and every time you apply your brakes. Most of these cheaper annoying modules will continue to flash your brake light(s) with the same irritating routine even when you are completely stopped in traffic. This is not only illegal and annoying it detracts from the visual appearance of your vehicle and other drivers/riders attention to the road. Some of these "zombie-like" flashers claim to have an accelerometer module that will supposedly give you a couple of hundreds milliseconds reaction time. We have experimented with these in our lab and road tests, they don’t work due to the nature of engine vibration, road vibration and mounting angle. Simply too many noise vectored components giving them very poor sensitivity. That is not the best way to implement this sort of technology. At best they are just for marketing. Be careful you always get what you pay for.

*Above product depiction is for show only. Actual connectors on unit ordered may differ.

Other Details

PDF Download:
10 Years!

Find Similar Products by Category

Product Reviews

Write your own product review

Showing reviews 1-10 of 11 | Next

  1. Simple and Works Great 5 Star Review

    Posted by on 22nd Aug 2019

    I just received mine and only took a few minutes to get it installed on my Thunderbird. Plug and Play simple. Plug is under the right cover. Programming took a couple of minutes and I was ready to ride. Would definitely recommend to anyone looking to improve visibility while riding.

  2. SupaBrake-3 5 Star Review

    Posted by on 21st Aug 2019

    Works exactly as advertised and very easy to install. My only issue was locating the brake-light plug on my ride, but once I found it I was done in no time.

  3. Works As Advertised 5 Star Review

    Posted by on 10th Jul 2019

    Priced right. Simple to install. High quality connectors and wiring. Stows easily under seat, hardly taking up any room. The options instructions are indeed a tad complicated but the basic setup that comes with the unit is just how I would do it anyway, so no issues here.

    What more could you want?

  4. Awesome as usual 5 Star Review

    Posted by on 5th Sep 2018

    This is my 3rd brake light modulator. Every time I trade my motorcycle, I get one. Super easy installation, connectors are perfect, and tons of customization. I use the default setup and am very happy with it.

  5. supabrake 3 5 Star Review

    Posted by on 21st May 2018

    easy to install and setup. works well and alerts other drivers behind you. a must have these days with so many on their phones and not paying attention.

  6. Supabrake III 5 Star Review

    Posted by on 6th Mar 2018

    Customer service was great. Fitment was perfect. Installation was easy, truly plug and play. The learning curve was steeper than I expected, and I had to re-read the instructions several times to fully understand how the variables interact to produce a result I liked. A video tutorial would be a great way to help the average rider figure this tech marvel out quicker.

  7. supabrake-3 Triump 4 Star Review

    Posted by on 6th Mar 2018

    Works great but way too complicated to program. In my retirement community you want flashing all the time when you hit the brakes, not a selective algorithm of flashes. Still. I would recommend.

    Bernard(vizi-tec): FYI... The SB3 can be programed to remove the GracePeriod. Thus it will yield "flashing all the time".

  8. Great product 5 Star Review

    Posted by on 23rd Feb 2018

    This is my second SupaBrake (one for my Yamaha and now one for my Triumph). Both have been great. They are extremely easy to install and have tons of programmable options - not that you have to worry about that if you like the stock programming (which I do).

    Overall a great product and based on the thank you / note cards that came in both orders, great people too!

  9. Supabrake-3 5 Star Review

    Posted by on 26th Oct 2017

    This unit is easy to install and program for numerous combinations of flashing patterns. It works great with my Triumph T120 LED brake light.

  10. SupraBrake III 5 Star Review

    Posted by on 25th Oct 2017

    So easy to install. Took all of 1 minute once I removed the rear rack which only took about 3 minutes.
    Excellent safety device. Thanks.

Showing reviews 1-10 of 11 | Next

Customers Who Viewed This Product Also Viewed

Sign up to our newsletter

Connect with us: Facebook