The latest SupaBrake product line for your Yamaha!
It's a proven fact that motorcycles can decelerate more rapidly than most cars and trucks. The combination of a motorcycle's narrow profile and the brisk change in velocity during braking is the most common cause of rear end accidents involving motorcycles, and often the results are fatal to the rider. Vizible Technologies' SupaBrake modulators are designed to enhance the reaction time of the vehicle behind you. It is designed to pulsate your vehicle's brake light(s) with a variable number of flashes calculated by its embedded algorithm. The algorithm is based on the rate at which you apply your brakes. As a result, the brake light(s) are flashed in a more subtle manner at lower speeds(when brakes are frequently used), and more aggressively at higher speeds(when brakes are not used for longer time intervals). Whereas other simpler products on the market that continuously "blink" their brake light(s) with an annoying repeating sequence - each and every time their brakes are applied! Our Supabrake product pulses in driving conditions when you need to get the immediate attention of drivers without annoying them.
Upon applying the brakes, the SupaBrake sends a burst of pulses to your motorcycle's brake light(s). The duration of the burst is a function of the time elapsed between the current brake cycle and the previous. After the burst, the unit allows the rear brake light to function normally(solid brake light). This algorithm is designed to eliminate target fixation as found in cheaper, passive versions that continuously "blink" the brake light(s) even though the vehicle is at a complete stop.
Example at low speed
When the frequency at which the driver/rider applies the brakes increases, (i.e. during low speeds such as city driving), the shorter the burst of flashes to the rear brake(s) light will be. If the brakes are applied within 0 - 12 seconds, the brake light will NOT flash - thus allowing it to function normally (solid brake light). This condition is most valuable during heavy stop-and-go traffic so as not to annoy the person or police in the vehicle behind you.
Example at cruising speed
When the frequency at which the driver/rider applies the brakes decreases, (i.e. at cruising speed), the longer the burst to the rear brake light will be. This condition is most valuable during quick sudden decelerations at speeds which require quick reaction to changes in traffic conditions or other driver's intentions. It has been scientifically proven that a quick flashing of a vehicle's brakes will alert the driver behind much sooner ... and the SupaBrake Flasher does this for you.
FEATURES & BENEFITS
Don't put other outdated bulkier modules on your motorcycle that pulsate your brake light each and every time you apply your brakes. Most of these cheaper annoying modules will continue to flash your brake light(s) with the same irritating routine even when you are completely stopped in traffic. This is not only illegal and annoying it detracts from the visual appearance of your vehicle and other drivers/riders attention to the road. Some of these "zombie-like" flashers claim to have an accelerometer module that will supposedly give you a couple of hundreds milliseconds reaction time. We have experimented with these in our lab and road tests, they don’t work due to the nature of engine vibration, road vibration and mounting angle. Simply too many noise vectored components giving them very poor sensitivity. That is not the best way to implement this sort of technology. At best they are just for marketing. Be careful you always get what you pay for.
Showing reviews 1-10 of 12 | Next
Posted by Stéphane on 23rd Aug 2018
Several good features and very granular in the configuration. Excelent service, quick response from Vizitec. With the addition of a decelerometer to activate the brake light, the product would have 5 stars.
Posted by Nathan Willis on 21st Aug 2018
So as an adv guy I've done more than a few farkles to my bike this is by far the easiest. 15 minutes and it's done using OEM connectors and works perfectly right out of the gate. I had planned on tweaking and customizing settings but honestly it performed better than I could have hoped with default settings. The smart features of this unit really put it miles above other brake light modulators. I will be putting this on all future bikes I own as well.
Posted by Michael Hildebrand on 16th Jul 2018
It works great. I was a little intimidated with the programming, but it's really simple once you do it.
Posted by Gary Sisco on 8th Jun 2018
Simple to install - simple to set-up- works great.
Posted by John on 18th Apr 2018
Good Product, Great Customer Service. I would buy from them again
Posted by Christopher on 26th Jun 2017
Great product, and easy to install with it being plug-n-play. The customer service is top notch. Bernard is excellent at replying to emails and very helpful. Will definitely do business again.
Posted by Dwight on 19th Jun 2017
Great product! Easy install since the connectors are set for you.
1 remove the seat
2 remove the left saddle bag
3 remove the left side cover
4 split the brake connector and attach the VIZI-TEC
Put it all back together after testing the brakes.
Posted by Charles on 4th May 2017
There's not much to say other than this is a great product that just works. There are lots of options and features you can change if you're so inclined, but I am just leaving it stock as it meets my needs.
Installation could not have been easier. Just disconnect the tail light connector under the seat and plug this in in series using included tie wraps to secure the kit. Put the seat back on and ride away.
Posted by Eric on 4th May 2017
Nice little personalized note with delivery. Installed well and works great. I wish however there had been some instructions as to where to find the connector to T into. I assumed the connector would be near the brake light, and proceeded to spend a couple of hours trying to get inside that assembly. Then I finally found something online that pointed me to the correct location under the seat, and the install would have only been 15 minutes.
Posted by Jong on 26th Apr 2017
The first unit didn't work. But it was promptly replace without drama. OEM connectors are great. End-to-end testing, splicing, tinning, soldering - just isn't for me. Great support and product!
Showing reviews 1-10 of 12 | Next